Posted: Mon Aug 07, 2006 5:31 am
What's wong with his pushbike?!boxerpan wrote:You need a CG125 if you are that way inclinedAde B wrote:Just doing my bit for the environmentanyone rides an S with a cat!!!!
Ade
Bailey.
Bailey.
www.boxertrix.com
The UK-based forum for BMW's sportiest Boxer motorcycles
http://www.boxertrix.com/phpBB2/
Bavarian beauty stripped (longish thread)
Page 2 of 2
Bailey.
Posted: Mon Aug 07, 2006 6:50 am
Ade
Take the cost of a Y piece out the grand that Jason's saveing you!!
Take the cost of a Y piece out the grand that Jason's saveing you!!
Posted: Mon Aug 07, 2006 9:08 am
Can you fit a cat to a pushbike ?bigblackfalco wrote:What's wong with his pushbike?!boxerpan wrote:You need a CG125 if you are that way inclinedAde B wrote: Just doing my bit for the environment
Ade
Bailey.
Posted: Mon Aug 07, 2006 9:15 am
Having passed an MOT without having to produce it, you're welcome to my Cat if you collect it...
John
John
Posted: Mon Aug 07, 2006 9:31 am
Nice work Chaps!
Jason - I''m surprised you haven't suggested putting a few packing washers in between the gearbox and engine so that the healthy bit of spline at the shaft end engages with the clutch plate.
Jason - I''m surprised you haven't suggested putting a few packing washers in between the gearbox and engine so that the healthy bit of spline at the shaft end engages with the clutch plate.
Posted: Mon Aug 07, 2006 12:05 pm
Now there's a thought.......julian wrote:Nice work Chaps!
Jason - I''m surprised you haven't suggested putting a few packing washers in between the gearbox and engine so that the healthy bit of spline at the shaft end engages with the clutch plate.
waste not want not
Posted: Tue Aug 15, 2006 8:34 am
Bits arrived yesterday - I was in Norwich all day... 
Car is in Norwich again today with wife... so I can only get up to sleaford tomorrow...
Should be just enough time to get the box back for't weekend.
Ade.
(I want my bike back...)
Car is in Norwich again today with wife... so I can only get up to sleaford tomorrow...
Should be just enough time to get the box back for't weekend.
Ade.
(I want my bike back...)
Posted: Tue Aug 15, 2006 6:10 pm
Ade - remember to get some Stainless Steel M6 bolts for the cat mateAde B wrote:Bits arrived yesterday - I was in Norwich all day...
Car is in Norwich again today with wife... so I can only get up to sleaford tomorrow...
Should be just enough time to get the box back for't weekend.
Ade.
(I want my bike back...)
Posted: Fri Aug 18, 2006 9:51 am
gearbox and shaft is supposedly on its return to me today big thanks to Steve at SED, he turned it round in a day.
Will pop down to new favourite shop Clerkenwell Screws to get exhaust bolts either this arvo or tomorrow am..
so will be over on Sunday am Jason all being well.
What else do I need?
Have loads of cable ties, assorted jubilees, copperslip - do I need to get any fancy grease, thread lock etc.??
Ade.
Will pop down to new favourite shop Clerkenwell Screws to get exhaust bolts either this arvo or tomorrow am..
so will be over on Sunday am Jason all being well.
What else do I need?
Have loads of cable ties, assorted jubilees, copperslip - do I need to get any fancy grease, thread lock etc.??
Ade.
Posted: Fri Aug 18, 2006 11:40 am
Paul can tell you the answer to that mate - just take the WD40 and gaffa tape....
Posted: Fri Aug 18, 2006 11:58 am
Found that place a month or so back.. superb. Been back for several more bits, although was a little surprised by the blank face when I asked for copperslipAde B wrote:Will pop down to new favourite shop Clerkenwell Screws
Nero