Exhaust questions... Simple upgrade not going to plan!

Got a technical query? Found another 0.02bhp? Ask/tell the world.

Moderators: Gromit, Paul, slparry

Heyho
Posts: 22
Joined: Sat Oct 07, 2017 7:36 pm

Exhaust questions... Simple upgrade not going to plan!

Postby Heyho » Wed Oct 25, 2017 8:00 pm

Evening all.

After deciding that my R1100S was a tad too quiet, and that the standard cat assy looked far too heavy and bulky, I ordered a Danmoto cat eliminator pipe. Simple job right? :lol:

It appears that these old girls are getting on a bit now, and whilst wiggling the rear silencer off of the cat pipe, the following happened:

Image

The scarcity of aftermarket silencers concerns me slightly, and I'm not keen on having to pay for a standard silencer. Before I embark on a fabrication project, does anybody know what other options I have available?

User avatar
Boxered
Route Master
Posts: 3079
Joined: Sat Jun 26, 2004 4:44 pm
Location: Sintelinns

Re: Exhaust questions... Simple upgrade not going to plan!

Postby Boxered » Wed Oct 25, 2017 11:34 pm

It has been a Looong time since I owned an 11S, ( just worked it out to be 11 years )
But if I recall correctly the STD end can(s) have a quite tortuous route after the up pipe exits the 1st silencer, so in effect if you could just seal the 2nd silencer off, you would not lose too much in the short term, this would give you time to pick up a used set of cans, IYSWIM?

Just to explain a little more, when an R1100S is running correctly, if you leave it running and look at the rear of the bike, you can see by putting your hand over each of the exhaust outlets that left is putting out a hell of a lot more than the right hand side.

I wouldn't recommend running around like this for too long, but it might buy you a little time to source a replacement end can(s)

HTH

( DISCLAIMER>>> I have just returned from the pub, so this might all be total bollox )
Well-weathered leather
Hot metal and oil
The scented country air
Sunlight on chrome
The blur of the landscape
Every nerve aware

User avatar
Boxered
Route Master
Posts: 3079
Joined: Sat Jun 26, 2004 4:44 pm
Location: Sintelinns

Re: Exhaust questions... Simple upgrade not going to plan!

Postby Boxered » Wed Oct 25, 2017 11:41 pm

Okay, now that my black coffee has kicked in, I can see that the up pipe is the one that has become detached from the end can(s)
so please ignore my previous post :oops:

Your best option is to source a good condition STD end can(s), people used to give them away as unwanted junk, but if you check ebay/german ebay(.de)
you may find something?

Steve, I'm off to bed now.....zzzzzzzzzzzzz
Well-weathered leather

Hot metal and oil

The scented country air

Sunlight on chrome

The blur of the landscape

Every nerve aware

metropolis2k
Posts: 380
Joined: Sun May 26, 2013 4:47 pm
Location: London

Re: Exhaust questions... Simple upgrade not going to plan!

Postby metropolis2k » Thu Oct 26, 2017 8:05 am

There's a couple of OEM ones on eBay for around £100, or you could hold out for an aftermarket one but you might be waiting a while! Probably much better options than trying to fix your old one.
2000 BMW R1150GS
2004 BMW R1100SS Boxer Cup Replica
2003 Yamaha R6 (trackday bike)

SP250
Posts: 982
Joined: Mon Sep 09, 2013 2:01 pm
Location: Shropshire

Re: Exhaust questions... Simple upgrade not going to plan!

Postby SP250 » Thu Oct 26, 2017 11:06 am

Get the gas bottles or Tig welder out and fix it.
Then search for some cans or adapt some for another bike.
John M

Heyho
Posts: 22
Joined: Sat Oct 07, 2017 7:36 pm

Re: Exhaust questions... Simple upgrade not going to plan!

Postby Heyho » Thu Oct 26, 2017 5:38 pm

Thanks for the replies chaps.

I think I will repair the existing silencer as suggested, at least I can eek out the last of the decent weather for this year.

I believe I've found a suitable stainless oval silencer with offset intake and single centre exit which looks like it will be fairly easy to modify to fit. Never have been a big fan of 2 into 1, then back into 2 for no reason other than aesthetics!

User avatar
nab 301
Member
Posts: 2374
Joined: Sat Dec 04, 2004 6:41 pm
Location: Dublin Ireland

Re: Exhaust questions... Simple upgrade not going to plan!

Postby nab 301 » Thu Oct 26, 2017 6:00 pm

Heyho wrote:Thanks for the replies chaps.
I believe I've found a suitable stainless oval silencer with offset intake and single centre exit which looks like it will be fairly easy to modify to fit. Never have been a big fan of 2 into 1, then back into 2 for no reason other than aesthetics!



I've had two identical breaks in the 100k odd miles that i've done . Both replaced with second hand items . Currently I have one spare that's cracked ...
I find the bike runs well with the y piece and standard cans . Any chance of posting up a photo of what you intend to use ? I'm always on the look out for potential replacements .
Gus on here fitted a standard looking bike can to the side a bit like a GS or jap inline 4.

viewtopic.php?f=4&t=3479&hilit=exhaust&start=30
Last edited by nab 301 on Thu Oct 26, 2017 6:15 pm, edited 1 time in total.
_________________
Nigel

Keep smiling, it makes people wonder what you've been up to!
1999 R1100s (mandarin) '
2018 DL 250V Strom
2019 CB125F Honda.
MZ301 Saxon Fun ( currently retired)
'03 Bullet 65 project..

kfrogzx7
Posts: 254
Joined: Tue Jul 15, 2014 9:25 pm
Location: Suffolk

Re: Exhaust questions... Simple upgrade not going to plan!

Postby kfrogzx7 » Thu Oct 26, 2017 6:05 pm

Expensive I know, but does anybody have these and any feedback on them ?

http://www.ebay.co.uk/itm/MUFFLER-EXHAU ... 4902.l9144

I think they're made by GPR ( Italian ), of which there are quite a few others listed on ebay without decent pictures.
Simon.
K100rs, R1100s, R1150rs, R1200st, K1300s

Heyho
Posts: 22
Joined: Sat Oct 07, 2017 7:36 pm

Re: Exhaust questions... Simple upgrade not going to plan!

Postby Heyho » Thu Oct 26, 2017 8:26 pm

nab 301 wrote:
I've had two identical breaks in the 100k odd miles that i've done . Both replaced with second hand items . Currently I have one spare that's cracked ...
I find the bike runs well with the y piece and standard cans . Any chance of posting up a photo of what you intend to use ? I'm always on the look out for potential replacements .
Gus on here fitted a standard looking bike can to the side a bit like a GS or jap inline 4.

viewtopic.php?f=4&t=3479&hilit=exhaust&start=30


I have been considering a side mounted silencer. The item I was looking at is:

http://www.ebay.co.uk/itm/2-ID-3-5x7-Ov ... SwjTlZgQeu

Dimension wise it looks good, provided the visible part is acceptable in terms of appearance.

User avatar
nab 301
Member
Posts: 2374
Joined: Sat Dec 04, 2004 6:41 pm
Location: Dublin Ireland

Re: Exhaust questions... Simple upgrade not going to plan!

Postby nab 301 » Fri Oct 27, 2017 7:50 pm

Heyho wrote:
nab 301 wrote:


I have been considering a side mounted silencer. The item I was looking at is:

http://www.ebay.co.uk/itm/2-ID-3-5x7-Ov ... SwjTlZgQeu

Dimension wise it looks good, provided the visible part is acceptable in terms of appearance.


Curious how much it weighs and also It suggests a straight through perforated tube which combined with a Y piece may be very loud!
_________________
Nigel

Keep smiling, it makes people wonder what you've been up to!
1999 R1100s (mandarin) '
2018 DL 250V Strom
2019 CB125F Honda.
MZ301 Saxon Fun ( currently retired)
'03 Bullet 65 project..

SP250
Posts: 982
Joined: Mon Sep 09, 2013 2:01 pm
Location: Shropshire

Re: Exhaust questions... Simple upgrade not going to plan!

Postby SP250 » Fri Oct 27, 2017 9:12 pm

Try these guys - reccommended to me by a couple of mates who build road specials and race bikes.
Good price and made in UK too. Free postage in UK.
https://www.fuelexhausts.com
John M

dave the german
Member
Posts: 3614
Joined: Tue Nov 01, 2005 4:35 am
Location: North East

Re: Exhaust questions... Simple upgrade not going to plan!

Postby dave the german » Sat Oct 28, 2017 4:43 am

SP250 wrote:Try these guys - reccommended to me by a couple of mates who build road specials and race bikes.
Good price and made in UK too. Free postage in UK.
https://www.fuelexhausts.com


Also heard good reports John - mate has one fitted to his Transalp
'15 R1200GS TE
'06 R1200S
'04 BCR
Yam SR 500 long term restoration
wanna win the lottery and ride my bike

dave the german
Member
Posts: 3614
Joined: Tue Nov 01, 2005 4:35 am
Location: North East

Re: Exhaust questions... Simple upgrade not going to plan!

Postby dave the german » Sat Oct 28, 2017 4:45 am

Check further down in this section under Laser Exhausts - I didn't think the price for a new Laser system was too much
'15 R1200GS TE

'06 R1200S

'04 BCR

Yam SR 500 long term restoration

wanna win the lottery and ride my bike

Heyho
Posts: 22
Joined: Sat Oct 07, 2017 7:36 pm

Re: Exhaust questions... Simple upgrade not going to plan!

Postby Heyho » Tue Oct 31, 2017 7:15 pm

I did consider the weight, but figured it probably couldn't be much heavier than the standard item!

As for noise, yes, I once had a TRX850 with remus straight through absorption silencers, and that could lay waste to a greenhouse from 50 yards! :lol:

User avatar
tanneman
Member
Posts: 1203
Joined: Wed Mar 04, 2009 8:26 pm
Location: Terra Firma

Re: Exhaust questions... Simple upgrade not going to plan!

Postby tanneman » Wed Nov 01, 2017 6:28 am

Either on here on on pelican there is a thread of how to improve the flow in the standard exhaust. There is a lot of baffles and a 180 deg turn before some of the gasses goes to the second muffler. With some skill both cans can be opened and the baffles replaced, the internals improved and closed up again. If you doubt your skill a descent fabricator can do the work. Don't know what it will cost but probably cheaper than a Remus or Laser end can.
'Let me check my concernometer.'


Return to “Boxertech”

Who is online

Users browsing this forum: No registered users and 46 guests