Centre Stand

Got a technical query? Found another 0.02bhp? Ask/tell the world.

Moderators: Gromit, Paul, slparry

Post Reply
User avatar
Skint
Posts: 130
Joined: Fri Feb 20, 2004 9:34 am
Location: I would mainly be sliding down the M1

Centre Stand

Postby Skint » Mon Mar 01, 2004 10:55 am

With constant use of the centre stand, the resistance is now very low. For example a sparrow could land on the handle bars which would cause the bike to rock off and go for a roll..
How do you tighted the centre stand, had a quick look but the bolt just spinns, so i assume that the bolt through a hole which is pinned?? is it a new bolt jobbo???
When can the Highway agency lay softer road coverings??

Now rides a mangled wreck... Ho Hum back to the K100
Top
User avatar
Paul
Wanna buy a sticker mister?
Posts: 2867
Joined: Mon Feb 16, 2004 8:44 pm
Location: Boxertrix Towers, Norfolk
Contact:
Contact Paul

Postby Paul » Mon Mar 01, 2004 11:51 am

Skint,

The back of the mounting block is round with two parallel flat sides taken off. This should mate into the the bracket on the bike. Try pushing the mounting from the back as you tighten the bolt at the front and hopefully it should push back into the seat, to allow you to tighten the bolt.

I've actually had the bolt shear on my centre stand, so check that out too. The replacement spindle and bolt should cost around £10 from your local BMW dealer, if worst comes to worst.

Good luck

Paul
You really need only two tools: WD-40 and duct tape. If it doesn't move and it should, use WD-40. If it moves and shouldn't, use the tape.
Top
babble53
Posts: 42
Joined: Mon Feb 23, 2004 4:23 pm

Postby babble53 » Mon Mar 01, 2004 12:42 pm

If your bike is rolling forward off the stand, mebe the stand is not comming forward enough. There's two bolts that act as a stop. between the frame and stand. mebe one's come loose?
Top
User avatar
Jason M
Posts: 1404
Joined: Wed Feb 18, 2004 7:56 am
Location: southampton

Postby Jason M » Mon Mar 01, 2004 4:27 pm

That's my guess too - I had to screw mine back in not long ago. 10 secs with a 10mm I think
Top
User avatar
stempy
Captain
Posts: 690
Joined: Wed Feb 18, 2004 8:41 pm
Location: I could tell you but then I'd have to kill you
Contact:
Contact stempy

Postby stempy » Mon Mar 01, 2004 7:00 pm

Those centre stand pivot bolts are done up with super ultra strength loctite for which a small thermonuclear device is required to shift them.
Top
User avatar
bigblackfalco
Posts: 1921
Joined: Wed Feb 18, 2004 10:05 am
Location: Darkest Aberdeenshire

Postby bigblackfalco » Mon Mar 01, 2004 11:13 pm

It must be said that it is not the best thought out idea.The stand inserts/bushes/collars whatever wear away really fast.
Got piss*d off with mine and took the bugger off.Job well done.
Bailey.
Top
User avatar
Skint
Posts: 130
Joined: Fri Feb 20, 2004 9:34 am
Location: I would mainly be sliding down the M1

Postby Skint » Tue Mar 02, 2004 10:31 am

Bailey, does that mean you got one of those paddock stands for it then?? I like the centre stand myself as its costs nowt..

Cheers all will look into it further..
When can the Highway agency lay softer road coverings??



Now rides a mangled wreck... Ho Hum back to the K100
Top
User avatar
bigblackfalco
Posts: 1921
Joined: Wed Feb 18, 2004 10:05 am
Location: Darkest Aberdeenshire

Postby bigblackfalco » Wed Mar 03, 2004 11:01 pm

The BMW stand is the dogs danglies.Much,much better than the centre stand.And the same price to buy.
Bailey.
Top
Post Reply

Return to “Boxertech”

Who is online

Users browsing this forum: No registered users and 26 guests